Four products sit under the word "cleanser" on a contract manufacturer's line card, and they have almost nothing in common on the factory floor. A balm is a solid that has to be melted, poured hot and cooled in the jar. An oil is a cold-mixed liquid that fights the pump it ships in. A micellar water is mostly water, which means preservation and microbiology decide whether it is safe to ship at all. A gel or foam is a surfactant system whose viscosity has to be built and then filled through a tube or foamer without collapsing. If you are choosing a cleansing balm and cleansing oil contract manufacturer in China and you have not yet picked the texture, pick it first — the texture decides which line your product runs on, what packaging you can use, which tests you must budget for and what 2,000 units actually costs.

This article compares the four on the terms a plant sees them — compounding, filling, packaging, testing, batch minimum — and finishes with what to put in the brief.

What each texture is, from the kettle's point of view

Marketing describes cleansers by what they do. A compounder describes them by phase and process.

  • Cleansing balm. Anhydrous. A blend of oils, waxes or solid esters, and an emulsifier that lets the oil rinse off with water. No water in the formula, so no aqueous-phase preservation challenge — but a melting point to manage. The balm is compounded hot until clear, held at temperature, poured into jars, and allowed to set. Everything that goes wrong with a balm goes wrong in the cooling.
  • Cleansing oil. Anhydrous and liquid. Oils plus an emulsifier, mixed cold or with gentle warming. The simplest thing on this list to compound. The difficulty moves downstream to packaging: low-viscosity oil in a pump bottle leaks, drips and back-pressures, and the choice of pump and closure is the real engineering.
  • Micellar water. Water plus a low level of mild surfactant, humectants, and a preservative system. Compounds cold in a plain tank in minutes. The cost is invisible: preservation, preservative efficacy testing, microbiological release testing, and a formula that stays clear and does not go cloudy on a shelf.
  • Gel and foam cleansers. Aqueous surfactant systems. Foam-format products are usually thin liquids dispensed through a foamer pump that aerates them at the nozzle; gel cleansers are thickened to a viscosity that holds in a tube. Both need preservation and both need viscosity control that survives temperature swings in transit.

Yadun Cosmetics, a contract manufacturer in Baiyun District, Guangzhou, lists all four — facial cleansers, cleansing oils, cleansing balms, micellar waters and makeup removers across foam, gel, oil and balm textures — on its cleansing and makeup-removal line, with tubes, bottles and jars filled in-house. That is a broad line card. Which of those textures the plant runs most often, and at what batch sizes, is the question the rest of this article helps you ask.

The manufacturing comparison

Cleansing balm Cleansing oil Micellar water Gel / foam cleanser
Water content None None ~90%+ High
Compounding Hot, to full melt; held at temperature Cold or warm mix Cold mix, minutes Cold or warm; viscosity built with thickener or surfactant structure
Filling Hot pour into jar; controlled cool Cold fill into bottle Cold fill into bottle Cold fill into tube or foamer bottle
Usual pack Jar (glass or PP), often with spatula Pump bottle, sometimes flip-top Bottle, flip-top or pump Tube; foamer pump bottle
Preservation Usually not required (anhydrous); antioxidant for oils Antioxidant Full preservative system, efficacy tested Full preservative system, efficacy tested
Key stability risk Sweating, graininess, sink-holes, melt in transit Oxidation/rancidity, pump leakage, cloudiness at low temp Cloudiness, microbial growth, pH drift Viscosity loss, phase separation, foam quality drift
Filling-line fit Hot-fill capable jar line with cooling tunnel or racking time Standard bottle line with pump-compatible nozzle Standard bottle line Tube line or bottle line with foamer closure
Relative compounding cost per kg Highest (energy, hold time, ester/wax raw materials) Medium (oil raw materials) Lowest (water) Low–medium
Relative pack cost per unit Highest (jar, lid, seal, spatula) High (pump) Low–medium Medium (tube) or high (foamer)

Read the last two rows together. The cheapest bulk — micellar water — usually goes into a cheap bottle. The most expensive bulk — balm — goes into the most expensive pack. Oils sit in the middle on bulk but high on pack because of the pump. This is why the "which is cheapest at 2,000 units" question has a different answer from "which has the cheapest formula".

Balm: the hot-pour problem in detail

A cleansing balm is the one texture on this list that requires a capability many general skincare lines do not have: pouring a product hot into a jar and controlling how it cools.

What happens on a balm line:

  1. The batch is compounded to full melt — for ester-and-wax balms this typically means somewhere in the 60–80 °C range, depending on the wax system — and held there so no unmelted solids carry through.
  2. Jars are filled from a heated hopper or heat-traced fill head. If the hopper cools, the balm starts to set in the nozzle and fill weights drift.
  3. Filled jars are cooled — on racks at ambient, in a cooling tunnel, or in a controlled-temperature room. The cooling rate decides the surface finish.

The defects, and what causes them:

  • Sink-holes and cratering. The balm contracts as it solidifies. Cooled too fast, the surface sets before the core and a dip or crack forms in the centre. Some plants do a two-stage fill — pour, let set, top up — to get a flat surface. That doubles the fill operation.
  • Sweating. Liquid oil separates to the surface over time, because the wax network cannot hold all the oil. This is a formula issue that shows up as a production issue on the first hot week in a container.
  • Graininess. Certain esters and butters crystallise into visible grains if cooled slowly through the wrong temperature band. The fix is either a formula change or a controlled cooling profile, and the plant has to be able to do the latter.
  • Transit melt. A balm with a low melting point ships fine from Guangzhou in January and arrives as a liquid in July. Ask for a heat-cycle stability test that reflects your actual route, not a generic one — the general framework for stability and shelf-life testing at a Chinese cosmetics OEM applies, with transit temperature as the extra variable.

Whether Yadun runs a hot-fill jar line, and what cooling it uses, is not published on its factory page — the page shows tubes, bottles and jars filled in-house and lists balms among the textures, but the pouring method is not stated. Ask directly, and ask to see a filled balm from a previous run after it has sat for a month.

Balms also carry the awkward pack. A jar needs a lid, usually an inner seal disc, often a spatula, and frequently a shrink band. Each is a component with its own MOQ, in the same way that a compact's parts are — the component-split logic in the companion article on cushion compact and BB cream assembly applies to balm jars in a lighter form.

Oil: cheap to make, awkward to package

A cleansing oil is a compounder's easiest job. It is the packaging engineer's headache.

Low-viscosity oils have three problems in a pump bottle: they wick past the pump seal and leak in transit; they drip after actuation because the pump's dip tube and chamber do not hold thin liquid cleanly; and some pump gaskets swell or harden in contact with certain esters. The remedies are a pump specified for low-viscosity oils (ask the pump supplier for the viscosity range the pump is rated for), a compatibility soak of the pump in the formula before committing, and a transit test with bottles on their side.

Two insider points:

  • The emulsifier that makes an oil rinse off is also what makes it turn cloudy in the cold. Some cleansing-oil emulsifiers solidify or haze below room temperature. A bottle that goes cloudy on a cold shelf will be returned as "gone off". A low-temperature stability check — a few days at refrigerator temperature — is cheap and is not part of every plant's standard protocol. Ask for it.
  • Oxidation is the shelf-life clock. With no water, there is no microbial risk, but unsaturated oils go rancid. Antioxidant choice, oxygen headspace in the bottle and the opacity of the pack all matter. An oil in a clear bottle on a bright shelf needs a different antioxidant load from the same oil in an opaque one.

Oils suit a standard bottle line — the kind shown on Yadun's floor — and are the most forgiving of the four to run at a modest batch size, which is why the oil is often the right first SKU when a brand is piloting a cleansing range.

Micellar water and gel: the preservation budget

Micellar water is the cheapest formula on this list to compound. It is water, a small amount of surfactant, some humectant, and a preservative system, mixed cold. A plant can make a tonne in a morning.

The cost sits in what has to happen around it:

  • Preservative efficacy testing (a challenge test) on the final formula, because the product is a near-ideal growth medium. This is a laboratory test with its own lead time, typically four weeks or more, and it has to be repeated if the formula or pack changes.
  • Microbiological release testing on each batch before it ships, because a contaminated water-based batch is a recall.
  • Water quality. The plant's purified-water system is the raw material. Ask what type it is and what monitoring it runs.
  • Clarity and pH stability over shelf life; micellar waters are sold clear, and a haze that develops in month four is a stability failure the customer can see through the bottle.

Gel and foam cleansers share the preservation burden and add viscosity control. A foamer format in particular is sensitive: the formula has to be thin enough to pass the foamer mesh and structured enough to build foam, and that window narrows if the surfactant blend changes. If you are considering a refillable or reduced-plastic foamer bottle — a live question for cleansing ranges, covered in this guide to sustainable and refillable beauty packaging from China — confirm the foamer's mesh and the formula together, not separately.

How Yadun preserves its water-based cleansing formulas, whether microbiological testing is run in its own lab or outsourced, and what its water system is, are not published. All three belong on your question list; none can be assumed from a line card.

Which is cheapest to run at 2,000 units

The honest answer is that it depends on pack size, and the arithmetic is worth doing before you brief.

Yadun's stated MOQ is 2,000 units. What that means in bulk terms depends on the fill:

Texture and typical pack Fill size (assumed) Bulk for 2,000 units (assumed) Comment
Balm, jar 90 g ~180 kg Small hot batch; fine on a small kettle, may be below a large kettle's minimum working volume
Oil, pump bottle 150 ml ~280 kg Cold mix; batch size is rarely the constraint
Micellar water, bottle 200 ml ~400 kg Trivial to compound; testing cost is fixed regardless of batch size
Gel/foam, tube or foamer 150 ml ~300 kg Cold mix; viscosity check per batch

Those fill sizes and bulk figures are assumptions for illustration, not the factory's numbers. The point they make is this: at 2,000 units none of the four is constrained by compounding capacity. What separates them in cost is (a) pack cost per unit, where jar plus spatula and pump bottle sit above tube and plain bottle; (b) fixed testing cost, where the water-based textures carry a challenge test and per-batch micro release that the anhydrous textures do not; and (c) process time, where the balm's hot pour and cooling consume line hours the others do not.

A rough ranking of total cost per unit at 2,000 units, holding formula quality equal, usually comes out: micellar water lowest, gel cleanser in a tube next, oil in a pump bottle above that, balm in a jar highest. That order can flip if the micellar water's testing has to be paid from scratch on a 2,000-unit pilot, or if the balm goes into a simple PP jar without a spatula. Ask the plant to quote each texture with bulk, pack, filling and testing shown as separate lines, and the ranking for your specific brief will be visible.

Per-texture minimum batch sizes at Yadun — whether a hot-pour balm run can be done at the same 2,000-unit floor as a bottle product — are not published. Ask, because a plant's kettle sizes often set a higher practical minimum for hot process than for cold.

What to put in the brief

Before you send a development request for any cleanser texture, decide and write down:

  1. Texture and format — one of the four, and the pack you intend, with a reason. "Balm in a 90 g PP jar with spatula" is a brief; "cleansing product" is not.
  2. Fill size and unit count, so the plant can size the batch and tell you whether hot process at that size is practical.
  3. Whether you want a house formula or custom development. Yadun's page states both are available, with standard formulations sampling in three days and custom in seven. A house cleansing oil is a fast pilot; a custom balm with a specific melt profile is a development project.
  4. Destination market, so the preservative and any other restricted-ingredient choices can be made against the right list — your obligation to specify, the plant's to formulate to.
  5. Stability tests you require — heat-cycle for balm, low-temperature for oil, challenge test and per-batch micro for water-based — and who pays for each.
  6. Pack compatibility tests — pump soak for oil, foamer function for foam, jar seal for balm.
  7. Component sourcing — who buys jar, pump, tube, spatula, and at what MOQ.

What to ask the supplier next

  1. Which of the four textures do you run most often, and on which line?
  2. Do you hot-pour balms in-house? How are jars cooled, and can I see a month-old retained jar?
  3. What is the practical minimum batch for a hot-process product versus a cold one?
  4. How are water-based cleansers preserved, and is challenge testing arranged by you or by me?
  5. Is microbiological release testing done in your own lab or sent out, and what is the turnaround?
  6. What is your purified-water system, and what records are kept?
  7. Can you quote bulk, pack, filling and testing as separate lines for each texture?
  8. Which pump, foamer and jar suppliers do you already run, and will you accept mine?

Yadun Cosmetics is a reasonable plant to put these questions to: a Baiyun District, Guangzhou contract manufacturer established in 2009 with 100–500 staff, cleansing and makeup removal across foam, gel, oil and balm textures on its third product line, tubes, bottles and jars filled in-house, compounding, lab and QC on site, a stated MOQ of 2,000 units, and production of 15–30 days after sample approval. Those are the company-stated terms. The texture-specific capabilities — hot pour, preservation, per-texture minimums — are what this article has left as questions, so read the factory profile for what is published and get the rest in writing before you commit to a texture.