Open a jar of body scrub that has sat in a warehouse for four months and you see the whole manufacturing problem in one glance: either an even, spoonable mass of particles held in a base, or a layer of clear oil on top of a compacted brick of sugar at the bottom. The formula was probably fine on the day it was sampled. What failed was the part of the brief nobody wrote — the rheology that keeps particles suspended, the filling method that keeps them evenly dosed jar to jar, and the choice of particle that survives the base it is sitting in.
This guide is for a buyer choosing a body scrub private label manufacturer in China and trying to write a brief that produces the first jar rather than the second. It covers the exfoliant materials that are still exportable to the main markets, how each behaves in a base, what "suspension" actually requires, how a scrub is filled without the particles sorting themselves out in the hopper, and what to inspect before you accept a lot.
Choosing the particle: what survives the base and what survives customs
The exfoliant is the product. Everything else in the jar is a carrier for it. The first decision is therefore which particle, and that decision is constrained from two directions — chemistry and legislation.
The chemistry constraint is simple and often missed: soluble particles cannot sit in a base that dissolves them. Sugar and salt both dissolve in water, so a sugar or salt scrub has to be built on an anhydrous base — oils, butters, esters, waxes — and any water that gets in, from the formula or from a wet hand in the shower, starts dissolving the abrasive. Insoluble particles (fruit-kernel powders, jojoba esters, pumice, silica, cellulose beads, bamboo) can go in either an anhydrous base or a water-based emulsion or surfactant gel, which opens up rinse-off shower-scrub formats that sugar cannot do.
The legislative constraint is microbeads. Solid plastic microbeads — polyethylene and similar — in rinse-off cosmetics have been prohibited in the United States since the federal microbead law of 2015 took effect, the United Kingdom banned their manufacture and sale in rinse-off products in 2018, and the European Union has restricted intentionally added microplastics under its chemicals regulation with a phased scope that started in 2023. Several other markets have followed or are following. The details differ — what counts as a microplastic, whether leave-on products are in scope, and the transition dates — so the exact wording has to be verified against the current text for each destination. For a brief, the practical rule is: no synthetic polymer particles of any kind, and a written statement from the factory to that effect on the raw-material list. If your target markets include the United States, the United Kingdom and the ASEAN countries, that statement is not optional.
| Exfoliant | Base it needs | Feel and cut | Manufacturing notes | Export note |
|---|---|---|---|---|
| Sugar (granulated, various grades) | Anhydrous only | Rounded crystals, medium cut, dissolves in use | Grade by sieve size; humidity in the plant can cake it; cheap | Widely accepted; check any food-grade sourcing claim |
| Salt (sea salt, dead-sea type, fine to coarse) | Anhydrous only | Sharper than sugar, coarse grades are aggressive | Hygroscopic; corrosive to some filling-head metals over time; can react with certain base ingredients | Widely accepted; provenance claims need documents |
| Apricot kernel / walnut shell powder | Either | Irregular sharp edges, strong cut | Natural colour varies lot to lot; dust hazard in weighing; consumer sentiment against "harsh" shell scrubs in some markets | Accepted; watch allergen labelling for nut-derived materials |
| Jojoba esters (spherical beads) | Either | Smooth, soft, low cut | Melt point matters — will deform if the base is hot-processed above it; most expensive per kilo | The standard replacement for plastic beads; supplier documents essential |
| Pumice, silica, bamboo, rice powder | Either | Fine to medium, "polishing" | Very fine grades settle slowly but also disappear into the base visually | Accepted; silica particle-size specification should be on file |
| Cellulose or wax beads | Either | Soft, decorative | Coloured beads can bleed dye into pale bases | Check that the bead is not a synthetic polymer under the destination definition |
| Coffee grounds, ground seeds, botanical fibres | Anhydrous preferred | Coarse, variable | High microbial load in the raw material; must be sourced treated and tested; colour and oil bleed | Accepted; raw-material micro testing must be on file |
Two things a good factory formulator will tell you unprompted. First, particle size is a distribution, not a number, and it needs to be specified as a sieve range (for example, "between 30 and 60 mesh, with under 5% fines below 100 mesh") because fines are what turn a scrub cloudy and what sink first. Second, coarse salt and coarse sugar are not interchangeable at the same weight, because their density and crystal shape differ, so a "20% exfoliant" brief means different things depending on which one you meant.
Suspension is a yield-stress problem, not a viscosity problem
Here is the detail that separates a formulator who has made scrubs from one who has made lotions. A thick product does not keep particles suspended. A product with yield stress does.
Viscosity describes how a fluid resists flow once it is flowing. Yield stress describes how much force it takes to make it flow at all. A particle sitting in a base experiences a tiny, constant downward force from gravity. If the base has no yield stress, that force is enough to move the particle — slowly, but for months — and it settles. It does not matter how viscous the base is; a very thick honey still lets a stone sink, just slowly. If the base has a yield stress higher than the force the particle exerts, the particle does not move, and the scrub looks the same at month six as at day one.
What builds yield stress depends on the base:
- Anhydrous oil-and-sugar or oil-and-salt scrubs get their structure from waxes, hydrogenated oils, butters, or structuring agents that form a network in the oil. Too little and the oil floats off the top within weeks; too much and the product is a solid puck that will not scoop. The window is narrow, and it moves with temperature — a scrub structured for a warehouse at 25°C can loosen in a shipping container at 45°C and never recover its network.
- Water-based emulsion scrubs use carbomers, acrylates crosspolymers or natural gums to create a gel network in the water phase that holds insoluble particles. These are the systems that let a cream scrub carry jojoba or bamboo without settling.
- Surfactant-gel shower scrubs rely on structured surfactant systems or added suspending polymers, because a plain clear surfactant solution has no yield stress at all and drops particles immediately.
The test is not "how thick is it." The test is the one the factory should run before you approve the sample: fill the actual jar, store it upright at elevated temperature and at room temperature for a period the stability protocol defines, and cut the product vertically to look for oil separation at the top and a particle gradient from top to bottom. A centrifuge test is a quick early screen, but it is not a substitute for real jars in a real oven. Ask for photographs of the sectioned jars, not a line on a report that says "no separation."
Emulsion body washes and shower gels — the base for a rinse-off scrub — draw on the same surfactant considerations as the sulphate-free shampoo brief, with the added complication that the suspending polymer has to survive whichever surfactant system you chose.
Filling a scrub without sorting the particles
Once the formula is stable in the jar, it still has to get into the jar with the right particle content in every unit. This is where a plant's equipment decides whether a scrub is a product it can actually run.
Standard lotion filling uses piston or gear-pump fillers with relatively narrow nozzles. Coarse salt, sugar crystals and shell powders do three unhelpful things in that equipment: they jam or wear the nozzle, they abrade seals, and — the subtle one — they separate in the hopper. A hopper full of scrub sitting still for twenty minutes while the line is adjusted lets particles drift, so the first jars off the line are particle-rich and the last are particle-poor. Both pass a weight check. Neither matches the sample.
What a scrub-capable filling setup looks like in practice:
- Large-bore piston fillers or rotary-lobe pumps with open passageways that pass particles without crushing them.
- A stirred or recirculated hopper so the mass stays homogeneous throughout the fill, not just at the start.
- Fill by weight rather than by volume for coarse scrubs, because volumetric dosing of a product with variable particle packing gives an inconsistent net weight.
- Temperature control on anhydrous scrubs that are filled warm so the structuring wax sets in the jar — pour too hot and the particles sink before the network forms; pour too cold and the product does not level and leaves voids.
- Wide-mouth jars and a headspace specification, because a scrub does not flow to fill the corners of a container the way a lotion does.
Jar filling also sets the cosmetic standard of the product: the top surface the customer sees when they open the lid. Anhydrous scrubs are often levelled or lightly pressed after filling, and any settling of the base during the first day in the jar shows as a dip in the surface. This is why a factory that fills scrubs routinely will tell you the jar has to sit a set time before capping, and why that dwell is a real constraint on line speed.
Yadun Cosmetics, a Guangzhou contract manufacturer, lists body scrubs within its body care line alongside lotions, washes and hand creams, in tube, bottle and jar formats, with tubes, bottles and jars filled and packed in-house. That tells you the jar format is run on site; it does not tell you which filling heads are used for particulate product or how the hopper is kept homogeneous, because the factory has not published those details. Ask for them specifically, and ask to see a scrub being filled — on video if not in person — before you place the order. For a broader picture of what a cosmetics filling line contains and what to check on it, see the guide to cosmetic filling and packaging lines for bottles, tubes and pumps.
Microbiology and the water the customer adds
Anhydrous sugar and salt scrubs are frequently described as "self-preserving" because there is no water for microbes to grow in. That is true of the product on the day it is sealed and largely untrue of the product after two weeks in a shower, when wet fingers have been in the jar repeatedly. The water that enters is trapped in an oily matrix with sugar — a nutrient — and the formulator's decision about whether and how to preserve an anhydrous scrub is one of the more contested judgement calls in the category.
Do not ask the factory to make that decision for you silently. Ask it directly: what is the preservation approach for this anhydrous scrub, and has a challenge test been run that simulates water ingress? For water-based and surfactant scrubs the question is more conventional — a standard preservative efficacy test in the final pack — but the botanical particles raise a second issue: the raw material itself. Coffee grounds, ground seeds and fruit fibres arrive with their own microbial load, and a plant needs incoming micro testing or a treated-material specification from the supplier before those go in a kettle. Ask for the raw-material COA for any botanical exfoliant.
Inspecting a scrub lot before you accept it
A scrub lot needs a different inspection plan from a lotion lot. Add these to whatever your standard pre-shipment inspection covers:
- Net weight on a sample across the run, not just from one pallet, and specifically from the first and last cartons off the line, to catch hopper separation.
- Particle content check: dissolve or wash a weighed portion of product from several jars and weigh the recovered insoluble particles (for insoluble types), or compare against the retained approved sample by visual grading for sugar and salt.
- Sectioned jar: cut one jar per sampled carton vertically and photograph the cross-section for oil layer and particle gradient.
- Surface condition: level, no voids, no oil pooling.
- Closure and induction seal integrity on wide-mouth jars, because scrub particles caught in the thread are a common cause of leakers.
- Retained sample comparison: colour, odour, grit feel on the back of the hand against the approved golden sample kept by both parties.
The general framework for a third-party pre-shipment inspection in China is described in the guide to product inspection before shipment; the six points above are the scrub-specific additions to that plan.
Common questions
Why does my sugar scrub sample look perfect but the production lot separated?
The most common reasons are a change in fill temperature between lab and line, a larger production kettle that cooled more slowly so the structuring wax crystallised differently, or a container that spent time above the temperature the network was designed for. Ask for the fill temperature and the cooling profile on the batch record, and ask whether the stability test was run on lab-made or line-made product.
Can I use a water-based cream base with sugar?
Not for any reasonable shelf life; the sugar dissolves into the water phase and the product loses its exfoliant. Pair sugar and salt with anhydrous bases, and use insoluble particles if you want a cream or a rinse-off gel.
Are jojoba beads a plastic?
Jojoba esters are hydrogenated plant-derived waxes, not synthetic polymers, which is why they became the standard replacement for polyethylene beads. You still need the supplier's documentation on file, and you need to confirm that your destination market's definition of a restricted microplastic does not capture the specific material and grade you are using.
Does MOQ change for a scrub versus a lotion?
The published MOQ of a plant applies to units, but a scrub has a second minimum hiding behind it: the exfoliant raw material. A coarse salt or a jojoba ester bought in for one project may set a practical batch size, and a wide-mouth jar with a custom lid may carry its own component minimum. Ask for all three — fill MOQ, raw-material minimum, component MOQ — and plan around the highest of the three.
What to ask the supplier next
Before you commit to a body scrub order, get written answers to these:
- Which exfoliant materials do you run today, and from which suppliers? Ask for the raw-material list with sieve specification and, for botanical particles, the microbiological COA.
- Do you have a written statement excluding synthetic polymer microbeads for export markets? If not, ask for one to be issued for your order.
- Which filling heads are used for particulate product, and how is the hopper kept homogeneous during the fill? Ask for a short video of a scrub run.
- Is fill by weight or by volume, and what is the net-weight tolerance across the run?
- What structuring or suspending system holds the particles, and what is the yield stress or equivalent test used to confirm it?
- Has the stability protocol included sectioned jars at elevated temperature, with photographs?
- What is the preservation approach for this base, and has water ingress been simulated in the challenge test?
- What are the three minimums — fill, exfoliant raw material, jar component — for this specific scrub?
Yadun Cosmetics is a workable reference point for the kind of plant to put these questions to: a Baiyun District, Guangzhou contract manufacturer with body care as one of eight lines, scrubs listed explicitly within it, jars filled and packed in-house, and stated terms of a 2,000-unit MOQ, three-day standard and seven-day custom sampling, and 15–30 days production after sample approval. Those are company-stated figures, and the particulate-filling specifics above are not yet published for this plant, so treat the profile as the starting point for the conversation and confirm each answer in writing. Read the factory profile with this checklist beside it.
