If you have ever sent "need 800 mm wide rubber conveyor belt, 100 metres, please quote" to three Chinese suppliers and received three prices per metre that differ by a factor of two, the problem was not the suppliers. Knowing what to send in a conveyor belt RFQ to a Chinese factory is the difference between buying a construction and buying a number. A price per metre on its own is an answer to a question you did not ask: the cheapest quote is almost certainly a lighter carcass with thinner covers, and you will find that out on the line, not on the invoice.
A fabric conveyor belt is specified on roughly eleven lines. Fill all eleven and a belting works can quote you a construction — carcass, plies, covers, length, joint — that you can compare like for like across suppliers and write into a purchase order. Leave three of them blank and every supplier fills the gaps with whatever makes their quote look best.
Why a price per metre is not a quote
A rubber conveyor belt is a laminated product. Under the top cover sit two to six plies of woven fabric, each bonded to the next with a skim of rubber; under the bottom ply sits a thinner cover. The cost of a metre of belt is dominated by three things: the total carcass tensile rating (how many plies and what fabric grade), the total cover rubber by weight (top plus bottom gauge, times width), and the compound grade of that cover. Change any one of the three and the price moves 20 to 40 percent while the belt still looks identical rolled up on a core.
That is why an unqualified "800 mm belt" can be quoted honestly at wildly different prices. One supplier assumed an EP 200/2 carcass with 3 mm and 1.5 mm covers in a general-purpose compound; another assumed EP 400/3 with 5 mm and 2 mm in an abrasion grade. Both quoted a real product. Neither quoted yours.
The eleven lines below put every cost driver into your hands, so the difference between quotes reflects the supplier's margin and process rather than their guess about your application. The same principle that applies to any product spec sheet sent to a Chinese factory applies here with more force, because belting has fewer visible features and more hidden ones.
The eleven lines
Send these as a table, not as prose. Suppliers in the Hebei belting district read spec tables all day; they do not read paragraphs well in a second language, and neither does their quoting software.
| # | Line | What to write | Why it moves the price |
|---|---|---|---|
| 1 | Belt width | mm, e.g. 800 | Every other line scales with it |
| 2 | Carcass type and tensile rating | e.g. EP 400 (polyester warp, nylon weft, 400 N/mm total) | Fabric grade is the single largest cost driver after cover rubber |
| 3 | Ply count | e.g. 3 plies | Sets carcass thickness, troughability and minimum pulley diameter |
| 4 | Top cover gauge | mm, e.g. 5 | Rubber by weight; wear life on the carrying side |
| 5 | Bottom cover gauge | mm, e.g. 2 | Rubber by weight; usually one third to one half of top |
| 6 | Cover compound grade | DIN 22102 X / Y / W or ISO 14890 H / D / L, plus heat, oil or flame-resistant if needed | Compound cost differs sharply between general-purpose and special grades |
| 7 | Length and end condition | metres, open-ended or endless; if endless, the exact endless length | Endless belts need a factory splice and a press wide enough to make it |
| 8 | Joint type | Open (customer splices), hot-vulcanised endless, or prepared for mechanical fasteners | Splice labour and press time; fastener-ready ends need a different edge finish |
| 9 | Material conveyed and lump size | e.g. crushed limestone, max 150 mm lumps, density 1.6 t/m3 | Determines whether the grade on line 6 is realistic |
| 10 | Working environment and temperature | Ambient and material temperature, indoor/outdoor, oil or chemical exposure | Pushes you off general-purpose compound at defined thresholds |
| 11 | Quantity, destination and delivery term | Rolls, metres per roll, port of discharge, Incoterms 2020 term | Roll length sets packing; destination sets the freight line in the quote |
Eleven lines, one table, sent as a PDF or a spreadsheet. If your quoting contact comes back asking about any of them, you have learned something about the supplier before spending anything.
Lines 2 and 3: the designation most buyers get half right
The belt designation "EP 400/3" is read as: EP fabric, 400 N/mm total belt tensile strength, 3 plies. The number is the total full-thickness rating, not per ply. A common mistake is writing "EP 400 x 3 ply" and meaning three plies of EP 400 fabric each — which would be an EP 1200/3, a very different belt. Write the designation as the standards do, with total strength then a slash then ply count, and add "total, full thickness" in brackets if you want to be safe. The ply and tension rating article in this series goes deeper on picking the number; for the RFQ, the point is only that you write it unambiguously.
Lines 4 and 5: put both gauges, or the supplier picks
Top and bottom cover thicknesses are two separate lines because they do two separate jobs. The top cover takes impact and abrasion from the material; the bottom cover rides on the idlers and mostly needs to protect the carcass. A supplier quoting on "cover 5 mm" alone will choose the bottom gauge, and the choice will not be generous. Write "5 + 2" or "5 mm top / 2 mm bottom" and the ambiguity goes away. How much rubber your line actually needs is a selection question covered in the cover gauge article; the RFQ just needs both numbers stated.
Line 6: grade letters are a commitment, not a description
When you write a cover grade to DIN 22102 or ISO 14890, you are asking the supplier to commit to a defined tensile strength, elongation at break and abrasion loss for the cover rubber. The grade letter is the only line on the sheet that later maps directly to a laboratory test you can commission on the delivered roll. If you leave it blank, the delivered cover is whatever compound was in the mixer that week, and you have no test to hold it against. If your duty includes heat, oil or a flame-resistance requirement, say so on this line and expect the quote to change — and expect to ask for a test report from a named laboratory rather than an assurance.
What the supplier will ask back, and what it tells you
A belting works that reads a complete eleven-line sheet should still come back with questions. Which questions tells you a great deal.
Questions that indicate a factory reading your application:
- "What is the minimum pulley diameter on your conveyor?" — an EP 400/3 with 5 + 2 covers has a minimum drive-pulley diameter below which the plies delaminate over time; a supplier asking this is checking the construction will survive your machine.
- "Is the belt troughed, and at what idler angle?" — a stiff, heavy-cover belt on a 45-degree trough at 800 mm width may not sit in the idlers; thinner belts trough better. A supplier who asks is thinking about ISO 703 troughability.
- "Is the endless length the belt length, or the conveyor centre distance?" — a good question, because buyers routinely send centre distance and forget the belt goes around two pulleys.
- "Do you want the cover grade tested, and by whom?" — a supplier volunteering the test conversation is one you keep talking to.
Questions that indicate a reseller or a price-only shop:
- "What is your target price?" before any technical question.
- "Which construction do you want, we have many" — asked after you have already specified one.
- Silence on lines 9 and 10, followed by a quote that ignores the oil exposure you described.
Adding the conveyor unit to the same RFQ
If you are buying the frame, drive and idlers alongside the belt, the belt table is not enough. A complete conveying unit is quoted from a general-arrangement drawing and a short data sheet:
- Conveyor length centre-to-centre, lift and incline angle — incline over roughly 18 to 20 degrees pushes you toward chevron or cleated belting, which changes line 6 and the press tooling needed.
- Capacity in tonnes per hour and belt speed in metres per second; from these the width on line 1 can be checked rather than assumed.
- Idler configuration — trough angle, roller diameter, spacing on carrying and return sides.
- Drive package — motor power, gearbox ratio, drum diameter, whether the drive drum is lagged.
- Loading and discharge arrangement — chute geometry, impact height, whether a skirt board or impact bed is fitted.
Some belting works quote belt and frame together so the two are matched; Jiutong Conveyor Belting, a Boye County works that lists rubber conveyor belting, transmission belting and complete conveying units, asks on its own page for a general-arrangement drawing before any unit order and states that layout, length, incline and drive package are project-specific. That is the right expectation to carry into any supplier: no drawing, no unit quote.
For transmission belting the data set is different again. Send pulley diameters, centre distance and duty cycle — hours per day, starts per hour, shock loading — and let the supplier size the section. A V-belt enquiry that specifies only "B section, 2,500 mm" has missed the drive rating entirely.
The pre-send checklist
Before the sheet leaves your desk:
- [ ] All eleven lines have a value. "Standard" or "as per your recommendation" is not a value — it hands the cost driver back to the seller.
- [ ] The designation on lines 2 and 3 is written as total N/mm slash ply count.
- [ ] Top and bottom cover gauges are separate numbers.
- [ ] The cover grade is written as a standard's letter, not as an adjective.
- [ ] Length states open or endless, and if endless, whether the figure is belt length or centre distance.
- [ ] Material, lump size and temperature are stated even for "light duty" — a supplier cannot tell packaging duty from quarry duty from a width.
- [ ] Quantity is in rolls and metres, with a maximum roll length or roll weight your site can handle.
- [ ] Destination port and Incoterms 2020 term are named, so the freight and packing lines in the quote are comparable across suppliers.
- [ ] You have asked, in the same message, what test report and what laboratory the supplier will use to prove the grade on line 6.
- [ ] You have asked for a quoted lead time for sample, for the first roll and for a repeat order, as three separate figures.
Send the identical sheet to every supplier on the same day. When the quotes come back, the spread between them is now information about the suppliers rather than about your specification — which is the only way to make sense of why Chinese quotes for the same spec differ.
Common questions
Can I skip the cover grade and just ask for "good quality rubber"?
You can, and every supplier will say yes. The words commit them to nothing measurable. A grade letter commits them to a tensile strength, an elongation and an abrasion loss you can have tested on a cut sample of the delivered roll. If you do not know which grade you need, say what the belt carries and ask the supplier to propose a grade — then have that proposal written on the quote as a standard designation before you accept it.
Should I send a sample of the old belt instead of a spec?
Send both if you can. A cut sample lets a supplier count plies, measure cover gauges and identify the fabric weave, which is faster and more accurate than guessing from a nameplate. But a sample does not tell them what the belt carried or at what temperature, so lines 9, 10 and 11 still need to be written.
How small an order will a belting factory quote?
It varies from one plant to another and the fact source for this article gives one data point only: Jiutong states an MOQ of one piece, with standard samples in five working days and production in 15 to 20 working days, all company-stated figures. Whether a single trial roll is priced at production rate or at a sample rate is not published; ask that directly. For any supplier, write the trial quantity on line 11 and ask for the trial price and the programme price on the same quote.
What if the supplier answers only with a price per square metre?
Some belting is quoted per square metre rather than per linear metre, which is fine as long as the construction is stated alongside. A price per square metre with no designation is the same problem as a price per linear metre with no designation. Ask for the designation on the quote in the standard form, and do not compare the number to other quotes until it is there.
What to ask the supplier next
With the eleven-line sheet sent and a construction quoted, the next round of questions decides whether you place a trial order.
- Ask for the quote to restate your eleven lines exactly, so the construction you are buying is on their paper as well as yours.
- Ask which lines the supplier changed from your sheet and why — a supplier who quietly substituted EP 315 for EP 400 has told you something.
- Ask which laboratory will test the cover grade and the full-thickness tensile, and whether the report will be issued to you as buyer, naming the roll number.
- Ask what the minimum pulley diameter is for the quoted construction, and check it against your conveyor before accepting.
- Ask whether the endless splice, if any, is made in the plant and what press width is available.
- Ask for the sample lead time, first-roll lead time and repeat-order lead time as three separate figures, in writing.
- Ask for a video of the press and vulcanising line producing a belt of the width you specified, since a registered company name is not proof of a press.
Jiutong Conveyor Belting is a usable example of the enquiry shape this article describes: its own page asks buyers to send belt width, ply count, cover gauge, working temperature and destination, or a conveyor layout, and undertakes to come back with a construction and a quote. Those are company-stated terms from a company registered in 2024 whose corporate-registry check was still open at listing, so treat the factory profile as the starting point for the questions above, not as a substitute for them.
