Buy a belt and a conveyor from the same supplier and you have made one purchase order out of what used to be two, which is convenient right up to the point where the belt tracks off the frame in week two and each half of the supplier's workshop blames the other. A conveyor idler roller and pulley lagging specification is how you stop that happening. The belt is a consumable with a designation; the hardware around it — the idler sets that carry it, the rollers inside those sets, the pulleys that drive and turn it, and the rubber or ceramic on those pulleys — is a machine with drawings. If the drawings are not in the quotation, the machine is not specified, and the belt is being asked to compensate for hardware nobody has written down.
This article covers what each piece of hardware does to the belt, the numbers a supplier needs from you and the numbers you need back, where lagging earns its cost, and what to ask before you accept a "belt plus frame" quotation as complete.
What each piece of hardware does to the belt
A troughed belt conveyor carries material on the belt's top run and returns the empty belt underneath. Along the carrying run the belt sits in troughing idler sets — commonly three rollers, a flat centre and two inclined wings, which fold the belt into a trough so it holds material. On the return run the belt rides on return idlers, single flat rollers or V-pairs. At each end sits a pulley: the drive (head) pulley turns the belt, the tail pulley turns it back, and on longer conveyors there are snub, bend and take-up pulleys that route the belt and tension it. Lagging is the layer bonded to a pulley's shell — rubber or ceramic — to raise friction on the drive pulley and protect the shell on the others.
Each of those touches the belt, and each of them can ruin it:
- Idler spacing sets how much the belt sags between sets under load. Too far apart and the belt sags, material shifts at every idler and the belt walks. Too close and the frame costs more than it should. Spacing is a calculation from belt tension and load, not a catalogue default.
- Trough angle — commonly 20°, 35° or 45° — sets carrying capacity, and also how far the belt has to bend to go from flat over a pulley into the trough. That bend is the transition distance, and a transition too short for the belt's tension rating stretches the belt edges and tears the carcass at the pulley. It is the single most common way a correct belt fails on an incorrect frame.
- Roller diameter and bearing set roller life and rolling resistance. A roller that seizes becomes a stationary bar under a moving belt, cuts a groove in the bottom cover in hours, and eventually saws the belt.
- Pulley diameter must be at or above the belt maker's minimum for the carcass — bending a belt round a pulley smaller than its rated minimum fatigues the plies and opens the splice. This is why the pulley diameter belongs on the belt enquiry and the belt construction belongs on the conveyor enquiry.
- Pulley crown and lagging control tracking and drive. A crowned tail pulley helps the belt centre itself; a drive pulley without enough friction slips, heats the belt cover and glazes it.
The belt designation you learned to read — ply count, tension class and carcass — is the input to all of that hardware. A supplier quoting belt and frame together should be able to show you the arithmetic connecting them.
The numbers a supplier needs, and the numbers you need back
The Baoding belting works Jiutong Conveyor Belting lists complete conveying units alongside its belting so that belt and frame can be quoted together, describes layout, length, incline and drive package as project-specific, and says to ask for a general-arrangement drawing before ordering. That is the correct shape of an offer. What the fact basis does not say is whether the idlers, rollers and pulleys are made in the plant or bought in from the surrounding Boye County cluster — which the profile describes as a district with a long line of belting and conveyor-roller works — or which roller diameters, bearing series, trough angles and lagging types are on offer. Those are the questions this section is built to make you ask.
Send this with the enquiry:
| You supply | Why it matters |
|---|---|
| Material: bulk density, lump size, moisture, abrasiveness, temperature | Sets belt width, trough angle, cover grade and idler class |
| Required capacity (tonnes per hour) and belt speed, or one of them | Sets belt width and the other |
| Layout: length between pulley centres, incline angle, any horizontal curves, where loading and discharge happen | Sets belt tension, idler spacing, transition lengths, drive location |
| Loading conditions: drop height, number of loading points, whether impact idlers are wanted | Sets impact idler spec under the chute |
| Environment: outdoor, wet, dusty, corrosive, ambient range | Sets bearing sealing, shell material, lagging choice |
| Power available: voltage, frequency, and whether the drive package (motor, reducer, coupling) is in scope | Sets the drive package |
| Belt already chosen, if any: designation, cover gauges, joint type | Fixes pulley minimum diameters and transition distance |
And insist on getting these back before you accept the quotation as complete:
| Supplier returns | What you are checking |
|---|---|
| General-arrangement drawing with pulley centres, incline, idler spacing on carry and return, transition distances | That the layout matches the site and the transitions are long enough for the belt |
| Idler schedule: trough angle, roller diameter, shell wall thickness, roller length, shaft diameter, bearing series, seal type, frame style | Roller life, and whether the sets are a recognised series or a one-off |
| Pulley schedule: diameter, face width, shell thickness, crown, shaft diameter, bearing housings, lagging type and thickness | Minimum diameter against the belt rating; drive friction; tracking |
| Drive calculation: belt tension at drive, power at shaft, motor size, service factor, take-up travel | That the belt rating and the drive agree, and the take-up can tension the belt |
| Belt specification tied to all of the above: width, carcass, cover gauges, joint | That the belt was sized for this frame and not pulled from a price list |
Two insider details on those schedules. First, idler class is a real thing: CEMA in North America publishes idler classes by roller diameter and shaft size against belt width and load (the B, C, D, E series and their successors), and ISO and DIN publish roller and idler dimension series (ISO 1537 for troughed idlers, DIN 15207 and DIN 22107 for rollers and arrangements). If the supplier's idler schedule cannot be mapped onto one of those series, you cannot buy replacement rollers anywhere else, and you are locked to that plant for spares. Ask which series the idlers follow. Second, the return idler is where cheap frames go wrong: buyers specify the carry idlers carefully and let the return run take whatever comes. A bare steel return roller under a belt carrying sticky material builds up, goes out of round and drives the belt sideways. Rubber-disc or spiral return rollers on the dirty side cost little more.
Rollers: the component that decides maintenance cost
A conveyor roller is a steel tube with a bearing at each end on a fixed shaft, sealed against whatever the conveyor lives in. Its design life is set by three things you can put on a specification: the bearing, the seal, and the shell.
- Bearing series. Deep-groove ball bearings in the 6204 / 6205 / 6305 / 6306 sizes are common across the industry for light to medium duty, moving up with roller diameter and load. The size sets load capacity; the manufacturer sets quality. Ask for the bearing brand and grade, and ask whether it is a sealed-for-life bearing or greased at assembly.
- Sealing. A labyrinth seal with a grease reservoir, sometimes with an outer rubber lip, is the usual arrangement. Seals decide whether the roller survives wet or dusty duty. A roller that "meets the standard" with a token seal will fail in a quarry in months.
- Shell. Tube diameter (89, 108, 133 and 159 mm are common metric sizes; 4, 5 and 6 inch in CEMA terms), wall thickness, and how the end discs are fixed — pressed, welded, or spun — govern how true the roller runs. Ask for the total indicated runout and the rotating resistance the plant checks to.
- Shaft. Diameter and end form (flats, threaded) must match the idler frame slots. A roller with the right diameter and the wrong shaft flats does not fit the frame you already have.
You can specify all of this on a project order, and you should. What you cannot do from a drawing is know who made the roller. In a belting cluster, rollers are commonly a separate trade from belting — the plant that presses the belt may well be buying rollers from a roller works down the road, assembling them into frames it fabricates, and selling the unit. That is normal. The problem arises only when it is hidden: if the roller maker is not named, the bearing brand is not stated, and the runout is not checked, the roller is a commodity with a paint job. Ask directly who makes the rollers and put the answer on the order.
Pulleys and lagging: where friction and money meet
The drive pulley transmits all the power to the belt through friction, and the lagging is where the friction lives. The choices, roughly in order of cost:
| Lagging | What it does | Where it belongs |
|---|---|---|
| Bare steel (no lagging) | Lowest friction; belt slips when wet | Non-drive pulleys on light, dry duty only |
| Plain rubber, bonded | Raises friction; protects shell; cheap to replace | Standard drive and tail pulleys, dry to damp |
| Diamond or herringbone grooved rubber | Grooves shed water and fines so the belt keeps contact | Drive pulleys on wet or dirty duty; grooved direction matters for drive vs tail |
| Ceramic (tiles in rubber, or dimpled ceramic) | High friction that holds when wet; very high wear resistance | Drive pulleys with slip problems, high tension, abrasive fines; a large premium |
Insider details on lagging that catch out first-time buyers of a complete unit:
- Rubber lagging has a hardness and a thickness, and both should be on the pulley drawing. A common range is around 60 Shore A for drive lagging, with harder or softer compounds for special cases, in thicknesses that the supplier should state. If the drawing says "rubber lagged" with no number, it has not been specified.
- Bonding is the failure mode. Lagging that peels at the edge under a wet belt is a bonding failure, and it depends on the shell surface preparation (grit blasting), the adhesive, and the cure — hot vulcanised lagging bonds more reliably than cold-bonded sheet, and the supplier should say which they use. The same distinction that governs a belt splice applies here.
- Ceramic on a tail pulley is money wasted. The tail pulley does not drive; it turns the belt. Ceramic belongs where slip actually happens, and a supplier who quotes ceramic on every pulley is quoting for the invoice, not the conveyor.
- Crown. A crowned pulley helps tracking on short conveyors but can hurt a belt with a stiff carcass on a wide pulley. Whether the tail is crowned or flat should be a decision, stated on the drawing, not an accident of what the shop had on the shelf.
Accepting the unit: inspection before it ships
A conveying unit is a machine and should be accepted like one. The factory acceptance test process for machinery from China applies with a few belting-specific lines added: the belt runs on the assembled frame at the plant, unloaded, for long enough to show it tracks true through the transitions; every roller spins freely by hand and none is noisy; lagging is bonded to the edge with no lift; the drive package matches the calculation. Ask for that run on video with the belt marking visible, and a photograph of each roller schedule item next to a rule.
Then think about how it ships. A conveying unit is long, and long crated machinery has its own crating and breakbulk logic: whether the frame ships in bolted sections or welded lengths determines whether it fits a container at all. Ask for the shipping split on the general-arrangement drawing, not after the quotation.
Common questions
If the supplier buys rollers from a neighbour, does that matter?
Not by itself. It matters when the roller maker is not named, the bearing is not specified, and there is no runout or resistance check at assembly. A plant that buys rollers and tells you who from, with the bearing brand on the schedule, is easier to buy spares from later than one that claims to make everything and cannot show the roller line.
Can I use my own idler standard and have the frame built to it?
Usually yes, and it is the right way to protect your spares position. Send the idler series (CEMA class, ISO or DIN dimension series) and the shaft end form, and have the frames cut to suit. Confirm the plant will build to it rather than substitute.
How do I know the transition distance is right?
Ask for it on the drawing in millimetres, at each pulley, and ask what belt tension rating and trough angle it was calculated for. Belt makers publish minimum transition lengths as a multiple of belt width for each trough angle and carcass type; the frame should equal or exceed that. If the belt supplier and the frame supplier are the same works, this is the one calculation they cannot blame on anyone else.
Does pulley lagging need replacing on a schedule?
Rubber lagging wears and is replaced when it is worn through or peeling; there is no fixed interval. Grooved lagging is finished when the grooves are gone. Ceramic wears very slowly but the rubber backing can debond. Ask the supplier for the lagging thickness new, so your maintenance crew has a wear limit to measure against.
What to ask the supplier next
- Are the idlers, rollers and pulleys made in your plant or bought in? If bought, from whom, and can the roller maker's schedule be issued with the quotation?
- Which idler series do your sets follow — CEMA class, ISO 1537, DIN 15207 — and what roller diameters, shaft sizes and trough angles do you build to?
- What bearing brand and series, seal type, shell runout and rotating resistance are checked at assembly?
- What lagging types do you offer, with rubber hardness, thickness and bonding method stated on the pulley drawing?
- Will the general-arrangement drawing show idler spacing, transition distances and the shipping split, and will you run the belt on the assembled unit on video before dispatch?
Jiutong Conveyor Belting quotes belt and frame together for project buyers, tells you to ask for a general-arrangement drawing before ordering, and states a one-piece MOQ with 15–20 working days production — company-stated terms. Whether the rollers under that belt come from its own shop or the roller works around it in Boye County is one of the open items on its factory profile, and it is the first thing to settle before the belt and the frame arrive as one order.
