Every fabric conveyor belt fails at the joint first, or it fails somewhere else because the joint was fine. That is the whole argument behind the conveyor belt splicing vulcanised vs mechanical fastener decision, and it is a decision you make on the purchase order — not one the installer makes for you on site with whatever tools are in the truck. When you send an enquiry for a belt, the supplier needs to know whether you want the belt delivered endless (spliced in the plant to a finished loop length), open-ended with prepared ends, or open-ended with a box of fasteners. Each of those is a different product, a different price, and a different set of things that can go wrong at the customs broker, the crane and the first week of running.

This article lays out the three joint families, what each one does to belt strength and to your installation schedule, when the factory splice is worth the freight penalty, and what you need to write into the RFQ so the belt arrives ready for the joint you actually intend to make.

The three joint families and what they cost you in strength

A fabric belt's carcass — the plies of woven polyester-nylon or nylon-nylon fabric under the rubber — carries all the tension. A joint is any place where that carcass is interrupted, and the interruption is where strength is lost. The three ways of restoring it are not equivalent.

Joint type How the carcass is reconnected Typical retained strength (general industry range) Time to make Where it is made
Hot vulcanised (stepped) Plies are stripped back in staggered steps, overlapped with tie gum, cured under heat and pressure Usually quoted at 80–100 % of belt rating when done to a recognised procedure Several hours cure plus prep; belt out of service Factory press or portable press on site
Cold bonded (chemical) Same stepped geometry, joined with two-part cold-cure adhesive, no heat Commonly lower than hot — often quoted in the 60–80 % range, depending on adhesive and prep Hours of cure at ambient; humidity and temperature sensitive Site, sometimes factory
Mechanical fastener (hinged plate, solid plate, wire hook) Plates or hooks clamp the belt ends; a pin or bolts carry the load Typically well below vulcanised; fastener makers publish ratings per fastener size against belt rating and thickness Under an hour with the right tool Site, by a crew with hand tools

Treat the percentages as the shape of the comparison, not as figures you can write into a contract. The number that belongs in a contract is the one from the fastener manufacturer's rating table (for fasteners) or from a splice test on your specific construction (for vulcanised joints). Ask for it, and ask which standard the test was run to. ISO 1120 covers the static strength test for mechanical fastenings on textile belts; a vulcanised splice is usually assessed against the belt's own tensile test method and the splice procedure the supplier follows.

Two things inside that table that a belt engineer will notice and a first-time buyer will miss:

  • The step length is the joint. A stepped splice on an EP belt is built with a step per ply, and the length of each step is set by the belt's tensile class — a higher tension rating needs a longer step so the shear area in the tie gum is large enough. A splice cut with short steps to save belt length holds on the bench and lets go on the incline. If a supplier quotes an endless belt, ask for the step length per ply on the splice drawing. If they cannot tell you, they are not cutting it themselves.
  • Fastener rating and cover thickness fight each other. Mechanical fasteners are sized to total belt thickness. A belt ordered with a heavier top cover than the fastener range allows either gets the cover skived back at the ends (extra work, a weak point) or gets a fastener size too big for the carcass. Specify the fastener size and the belt gauge together, on the same line of the order.

What "joint type specified per order" actually means

The Baoding belting maker Jiutong Conveyor Belting lists joint type alongside width, ply count, cover gauge and compound grade as things fixed per order, and lists replacement belt lengths and joints for existing installations as an application. That is the normal way a fabric belting works quotes: the joint is a line item, not a default. What the fact basis does not say — and what you must therefore ask — is whether the plant makes endless hot-vulcanised belts in its own press, what the maximum width its splice press accepts, and whether splice kits, cold adhesive or fasteners are shipped with an open-ended belt. None of those is published, so none is assumed here.

There is a practical reason the question matters more for a smaller plant. A works with a company-stated headcount of ten to fifty is, in belting terms, a modest press line. Hot splicing a wide endless belt needs a splice press at least as wide as the belt plus a curing schedule that ties up the press for hours. Some cluster works do that in-house; others send the splice out to a neighbouring shop. The Boye County belting cluster, where this company is registered, is described in the profile as having compounding, fabric supply and vulcanising capacity close by — which is exactly the environment in which a splice can be subcontracted without you ever knowing. That is not a defect. It is a reason to ask who makes the joint and to have it named on the order.

When to order endless from the factory

Ordering a belt endless means the factory hot-splices it to your finished loop length before shipping. You get the strongest joint family, made in a press under controlled heat and pressure, by people who do it daily. You also take on a set of constraints that catch buyers out.

The length is now a hard number. An open-ended belt can be trimmed on site; an endless belt cannot be shortened without cutting out the splice you paid for. Your finished loop length must account for pulley diameters, take-up travel and the position of the take-up when the belt is new. A general working method is to measure the loop with the take-up in its start position, then subtract a small allowance so the belt can be tensioned. If your conveyor has never run, you are working from the general-arrangement drawing, and the drawing had better be current.

Packing changes. An endless belt ships as a loop, which is either rolled flat in a figure-of-eight or wound onto a core as a double thickness. Both make a larger, more awkward roll than the same belt open-ended, and both are harder to thread onto a conveyor: an open-ended belt is pulled through the structure and joined; an endless belt has to be fed over the pulleys, which on some frames means dropping a pulley out. Ask the supplier for the shipped roll dimensions and confirm your crane and your pulley access before you commit to endless.

Lead time carries the splice. Company-stated production of 15–20 working days at this factory covers the belt; whether the splice adds to that is not stated and should be asked. The sample-to-production timeline you agree needs the splice inside it, not bolted on afterwards.

Endless is the right answer when the belt is short enough to handle as a loop, the conveyor is designed for it, the duty is heavy enough that fastener strength is marginal, or the belt runs through scrapers and skirting that chew mechanical joints. Food and grain lines usually prefer it because a fastener line traps product.

When to order open-ended

Open-ended is the default for long belts, for replacement belts going into a running plant, and for any site where the conveyor is already assembled with the pulleys in. It leaves you three choices for the joint, and you should make that choice before ordering because it changes what the factory ships.

Open-ended for a site hot splice

The belt ships plain-cut. A splicing crew — yours, a contractor's, or one the supplier arranges — strips the plies, builds the step, and cures it with a portable press. You need the right tie gum and cover rubber for the belt's compound, cut from the same compound family, with the cure temperature and time matched. Ask the factory whether they will supply a splice kit (tie gum, cover strip, cement) matched to the belt, and whether the kit carries a shelf-life date. Uncured rubber kit material ages; a kit that has sat in a warehouse for a year is a splice that fails in month three.

Open-ended for a cold bond

The same stepped geometry, joined with a two-part cold-cure adhesive at ambient temperature. Cold bonding is the honest middle ground: no press, no power, no heat, but a joint that is sensitive to surface preparation, humidity, temperature and the operator's patience. The adhesive has a pot life, the joint has a cure-to-tension time, and both are on the adhesive maker's data sheet rather than the belt maker's. Do not accept a cold-bond quote without the adhesive brand and grade named.

Open-ended for mechanical fasteners

The belt ships plain-cut or with the ends squared. Fasteners are chosen by belt thickness, tension rating and minimum pulley diameter — the fastener maker's selection chart does that job. Two details belong on the order: whether you want the belt ends skived so the fastener sits flush with the cover (which reduces scraper damage and is worth asking for), and whether the factory can supply the fasteners at all or whether you are buying them locally. Buying fasteners locally is often the safer route, because the fastener brand your maintenance crew already owns the tools for is the one they will fit correctly at two in the morning.

The specification lines that prevent the wrong belt arriving

A belt order that does not settle the joint produces one of three surprises: an endless belt that will not thread onto the frame, an open-ended belt with no kit and no fasteners, or a belt whose cover is too thick for the fasteners in the store. Each is avoidable with a few lines in the RFQ. Build them into the same document you would use for any product spec sheet sent to a Chinese factory.

  1. Joint form: endless (hot vulcanised) / open-ended for site hot splice / open-ended for cold bond / open-ended for mechanical fasteners. One box ticked.
  2. If endless — the finished loop length, how it was measured, the take-up position at measurement, and the splice geometry you expect (stepped, number of steps, step length per ply, splice angle to belt centreline). Ask for a splice drawing in return.
  3. If open-ended — the cut length, including the splice allowance for the joint type you chose. A stepped splice consumes belt: the overlap length is lost from the running length. Ask the supplier to state the allowance they added.
  4. End preparation: plain-cut, squared, skived for fasteners, or stepped and prepared for a site splice. Prepared ends should be protected in transit; ask how.
  5. Kit and consumables: whether tie gum, cover strip and cement matched to the compound are included, their quantity, and the manufacture date on each. For cold bond, the adhesive brand and grade. For fasteners, the size and brand or an explicit statement that none are supplied.
  6. Who makes the joint and where: in the plant, at a named subcontractor, or at your site by whom. Name it.
  7. Splice strength evidence: for an endless belt, a splice test result on the same construction from a named laboratory, or the plant's own test with the method stated. For fasteners, the fastener maker's rating table for the size supplied.
  8. Carcass and cover details that govern the joint — ply count, tensile class, cover gauge top and bottom — because the tension rating on the belt designation is what sets the step length in the first place.

Common questions

Can a vulcanised splice be made on a belt that was ordered for fasteners?

Yes, provided there is enough belt. A stepped splice consumes overlap length; a belt cut exactly to the fastener length will end up short once the steps are cut. If you think you might convert to a vulcanised joint later, order the extra length now and state on the order that the ends are to be plain-cut, not skived.

Is a factory endless belt stronger than a site hot splice?

Usually more consistent rather than categorically stronger. Both are hot vulcanised; the factory press gives repeatable heat, pressure and alignment, and the crew works on the same constructions daily. A good site crew with a well-maintained portable press can match it. A poor site splice on a cold, damp night cannot. The advantage of the factory splice is that it removes the site variables — which is also why you should ask to see it: request photos or a video of the splice press and the splice being built for your belt, the same way you would ask for a walkthrough of the press and vulcanising line before a first order.

Why do mechanical fasteners wear out the belt around them?

Because the load that the whole carcass used to carry across its full width is now concentrated at the fastener teeth or bolt holes, and because the fastener stands proud of the cover and takes a hit from every scraper, skirt and pulley it passes. Countersinking or skiving the ends helps; so does choosing a fastener size properly matched to the belt's thickness rather than the biggest one in the box. On a belt that runs through a lot of cleaning equipment, budget to re-fasten on a schedule.

What to ask the supplier next

Before you sign off a belt order with a joint on it, get these answered in writing:

  • Do you hot-splice endless belts in your own press, and what is the maximum belt width and loop length the press accepts?
  • If the splice is subcontracted, who does it, and will the splice test and the splice drawing be issued in their name or yours?
  • For an open-ended belt, what end preparation ships as standard, and what splice kit or fastener supply is included — with quantities and manufacture dates?
  • What splice allowance did you add to the cut length, and what step length per ply do you use for this tensile class?
  • Can you show a video of a splice being built on the same construction, and a test report from a named laboratory for that splice?

Jiutong Conveyor Belting, the Boye County belting works profiled on CMH, is a reasonable example of where those questions land: joint type is specified per order, MOQ is a company-stated one piece, replacement lengths and joints are a listed application, and whether the endless splice happens inside the plant is exactly the kind of thing the profile leaves open for you to confirm. Read the factory profile with that list in hand and put the answers on the purchase order rather than in an email thread.