A qi wireless charging pad 15w output steps specification reads like a simple ladder — 5, 7.5, 10, 15 — and a buyer new to the category assumes the number is what the phone gets. It is not. The wattage steps on a wireless pad describe what the transmitter coil can push under the protocol the receiver asks for, and three separate things have to line up before a phone on that pad sees anything close to 15 W: the Qi profile the pad implements, the profile the phone's receiver accepts, and the adapter feeding the pad from the wall. Get any one wrong and the pad drops to 5 W, silently, with the LED still glowing.
This article explains what each step really means, why the same pad charges two phones at different rates, what the input adapter has to supply, how foreign-object detection and thermal cut-back decide real-world speed, what Qi2 changes, and how to write all of that into a spec a Chinese wireless-charger factory can quote against without leaving the important numbers blank.
What the four steps mean under the Qi standard
Qi is the Wireless Power Consortium's inductive charging standard. It is not one power level; it is a set of profiles, and the number printed on a pad is the ceiling of whichever profile that pad implements.
| Output step | What it corresponds to | Who gets it | What decides whether it engages |
|---|---|---|---|
| 5 W | Baseline Power Profile (BPP) — the original Qi level every certified receiver supports | Any Qi phone, earbud case, wearable | Coil alignment and a 5 V/2 A or better input; this is the fallback everything drops to |
| 7.5 W | A proprietary extension used by one major phone platform, layered on BPP with a specific frequency and a handshake | Only phones of that platform, and only if the pad implements the extension | Pad firmware licensed or engineered for that handshake; some designs deliver 7.5 W only with a specific input adapter |
| 10 W | Proprietary fast-charge extensions used by several Android phone makers, or the lower end of EPP | Phones from those makers, and any EPP receiver that requests 10 W | Receiver identifies itself and requests the mode; pad must implement that maker's protocol or EPP |
| 15 W | Extended Power Profile (EPP) — the Qi standard's higher level, up to 15 W, with authentication from Qi 1.3 onward | EPP-certified receivers; under Qi2's Magnetic Power Profile, 15 W with magnetic alignment | EPP negotiation succeeds, adapter supplies enough input (typically 9 V/2 A or a PD 9 V rail), thermal headroom exists |
Points that separate a pad that delivers from one that only claims:
- The 7.5 W and 10 W steps are not Qi levels. They are phone-maker extensions that the pad's controller has to implement, and a controller that implements one does not implement the other automatically. A pad advertised as "5 / 7.5 / 10 / 15 W" is, in practice, a pad running one or two controller firmware packages that handle several handshakes. Ask which handshakes are in the firmware and which phones the factory tested against — with model names, not "supports all phones".
- 15 W under EPP requires authentication from Qi 1.3. A Qi 1.3 receiver checks the transmitter's certificate before it will accept more than 5 W. A pad that is not Qi-certified, or that carries a certificate for a different model, can be limited by the phone to BPP. This is the single most common reason a "15 W" pad charges a new phone at 5 W.
- The step the pad negotiates is not the power the battery sees. Inductive transfer between two coils, through two cases of plastic and an air gap, is roughly 60–80 % efficient at good alignment and much worse when the coils are offset. A pad negotiating 10 W delivers perhaps 6–7 W into the phone's charge circuit, and that circuit then loses more. Buyers who benchmark a pad against a wired charger and expect parity are measuring the wrong thing; benchmark against the wattage step the phone reports, at fixed alignment, at 25 °C.
The input adapter: the part of the spec most RFQs forget
A wireless pad is a power converter, not a power source. To deliver 15 W into a coil it has to draw more than 15 W from its input, and the input has to be at a voltage the pad's transmitter stage can use. Most 15 W pad designs need a 9 V or 12 V input at 2 A or more — supplied over USB-C from a PD adapter offering a 9 V PDO, or over USB-A from an adapter running a legacy fast-charge protocol.
That creates three failure modes a buyer can specify away:
- Pad shipped without an adapter. The end customer plugs it into whatever 5 V/1 A brick is in the drawer. The pad's input negotiation fails, the controller falls back to BPP, and the "15 W" pad charges at 5 W or not at all. If you sell the pad without an adapter, print the minimum input requirement on the box and in the listing; if you sell it with one, the adapter is part of the product spec and part of the safety file.
- Adapter that advertises the right voltage but not enough current. A 9 V/1.67 A (15 W) adapter feeding a 15 W pad leaves no headroom for conversion loss; the pad throttles. A 9 V/2 A or 9 V/2.22 A adapter is the usual floor. If the pad is USB-C input, specify the PDO the pad requests, and check it against the adapter's PDO ladder — the same ladder logic that governs how a PD charger's output profiles are specified applies to the adapter you bundle.
- Cable in the box that cannot carry the current. A thin USB-A-to-C cable with high resistance drops the input voltage under load enough to trip the pad's under-voltage lockout. Specify the cable's length and conductor gauge, and ask the factory to test the pad with the bundled cable, not a bench lead.
For a supplier that builds both pads and the adapters that feed them — Lexiang Power's page lists Qi pads, in-wall units and multi-device stands at 5, 7.5, 10 and 15 W alongside USB and USB-C PD chargers from the same plant — there is an obvious question to ask: which of their own adapters is the qualified input for each pad model, and is that pairing in the test report.
Foreign-object detection and thermal cut-back: where the real speed is set
Two protective functions decide what a pad delivers over a 90-minute charge, and neither appears on the retail box.
Foreign-object detection (FOD) stops the pad from heating a coin, a key or a metal-backed phone case that has landed on the coil. The pad measures the power it transmits against the power the receiver reports back and cuts off when the loss exceeds a threshold. Two insider points:
- FOD calibration is per design and per coil batch. A pad tuned on one coil supplier's part and built on another's will have a shifted FOD threshold and will either false-trip on legitimate phones (customer complaint: "it keeps stopping") or fail to trip on a real object (customer complaint: "it got hot"). This is why the coil supplier and the coil count per model belong in your spec and in the change-control clause of your contract — a coil change is a re-qualification event, not a like-for-like substitution.
- Qi certification tests FOD against defined reference objects. An uncertified pad has been tested against whatever the factory chose. Ask for the FOD test record with the objects used.
Thermal cut-back reduces the output as the coil, the ferrite or the phone's battery warm up. Under EPP the receiver can also request a lower power as its own battery heats. The practical result is that a 15 W pad often delivers 15 W for the first ten or fifteen minutes and then settles at 7–10 W for the rest of the session. That is normal and compliant; the spec question is at what surface temperature the pad cuts back and to what level, and whether the LED indicates it.
Ask the supplier for a charge-curve log — power negotiated versus time, with pad surface temperature — on a named reference phone at 25 °C ambient. Lexiang Power's page lists a high/low-temperature chamber and in-process combined testers on site; it does not publish a thermal cut-back figure, so ask what the rig is run to and what a pass looks like.
Qi2 and the Magnetic Power Profile
Qi2 adds the Magnetic Power Profile (MPP): a ring of magnets in the pad and in the phone that snaps the coils into alignment, plus a revised protocol that delivers 15 W to any MPP-certified receiver regardless of phone maker. For a buyer the consequences are:
- Alignment stops being the customer's problem. The efficiency loss from offset coils, and a fair share of the FOD false-trips, disappear when the magnets hold the phone in place. Charge curves become repeatable in a way flat pads cannot match.
- The magnet ring is a mechanical and a certification item. Magnet grade, ring geometry and polarity are specified by the WPC; a pad with a magnet ring that is not to the MPP layout may hold the phone but will not certify. Housing tooling that was designed for a flat pad usually cannot simply have magnets added — the ferrite, coil position and case thickness over the coil all move.
- Qi2 certification is a separate listing from Qi 1.3 EPP, again per model and per holder. If you are specifying a new design in this cycle, decide up front whether it is a flat EPP pad or an MPP pad; a design that tries to be both without certification for either ends up as a 5 W product in the field.
Whether a given factory builds to Qi 1.3, to Qi2 MPP, or to neither is a question for the RFQ. It is not on Lexiang Power's CMH page, so it goes on your list below.
Compliance and paperwork, written as requirements
None of the following is something to assume a supplier holds. Each is something you require, per model, with the document in hand before you ship.
- Qi certification — a listing in the WPC's public product database under a named member company, for the exact model. Ask which of the supplier's legal entities is the WPC member and the listed holder, and look the model up yourself.
- Safety — for a pad sold with its adapter, the adapter's safety file (UL or ETL listing for North America, EN 62368-1-based CE file for the EU, the UK's own conformity marking for Britain) plus the pad evaluated as the load. For a pad sold alone, the pad's own safety evaluation as a USB-powered device.
- Radio and EMC — a wireless charger is intentionally radiating in the 100–200 kHz band. In the United States that means FCC authorisation under Part 15 or Part 18 depending on how the product is classified; in the EU the Radio Equipment Directive applies, with the RED declaration and the technical file behind it. The method in checking a Chinese supplier's CE and FCC paperwork applies directly.
- RoHS and REACH for the EU, with a declaration and substance test reports for the coil, the ferrite and the housing.
- Patents — the CMH page for this supplier lists two Chinese patent numbers on its multi-function wireless charger, a utility model and a design registration, and states they are registered to the Shenzhen entity. A patent number is a claim you can check: look both numbers up on the CNIPA register, confirm the holder name and the legal status, and only then treat the design as the supplier's own. Do the same for any patent number any supplier quotes.
Writing the spec: a checklist
Put this block in your RFQ, next to the general document set covered in what to ask a Chinese supplier before the first order.
- Qi profile and version — BPP only, EPP under Qi 1.3, or Qi2 MPP — and whether the model is certified, under which entity, with the WPC listing number.
- Proprietary steps required — name the 7.5 W and 10 W handshakes you need and the phone models the factory must demonstrate them on.
- Input — connector type, required input voltage and current, the PDO or legacy protocol the pad requests, and whether an adapter and cable ship in the box.
- Coil configuration — coil count, coil supplier, and a change-control clause requiring re-qualification if the coil or ferrite changes.
- FOD — test objects and thresholds, and the false-trip test on the phone cases you sell with the product.
- Thermal — surface-temperature cut-back point, the power level it settles to, and a charge-curve log on a named phone.
- Efficiency — input power versus negotiated output at 5 W, 10 W and 15 W, at defined alignment offsets (0 mm, 5 mm, 10 mm).
- Indicator behaviour — what the LED does on charge, on full, on FOD trip and on thermal cut-back, because the customer support script depends on it.
- Compliance requirements by market — Qi, safety, radio/EMC, RoHS, written as requirements with the standard named.
- Sample evidence — the charge-curve log, the FOD record, the efficiency table and the WPC listing screenshot, delivered with the sample and reviewed before the sample-to-production sign-off.
What to ask the supplier next
Send these with the RFQ and file the answers against the purchase order:
- Which Qi version each pad model is built to, whether it is WPC-certified, and under which legal entity.
- Which proprietary 7.5 W and 10 W handshakes are implemented and which phones they were tested on.
- Coil count and coil supplier per model, and what happens to the FOD calibration if either changes.
- The qualified input adapter for each pad, and whether the pairing is in the test report.
- The thermal cut-back point, the settled power level and a charge-curve log at 25 °C.
- Which of the two Chinese patent numbers listed on the profile covers the model you are buying, so you can check it.
- MOQ, sampling lead time and volume lead time in writing — the CMH page lists all three as "contact via CMH".
Lexiang Power is a sensible place to test that list: a Yichang-built, Shenzhen-fronted power-supply maker that launched its wireless range in 2020 and lists Qi pads, in-wall units and multi-device stands at 5, 7.5, 10 and 15 W, with two Chinese patent numbers on the multi-function design. The page tells you the steps exist; it does not tell you which Qi version, which coil or what the pad delivers at minute forty, and neither does this article. Read the factory profile, send the spec block above, and judge the answer on the charge-curve log, not the ladder on the box.
