An oil resistant conveyor belt NBR cover compound is the standard answer when a belt starts swelling, and it is often the right one. But the symptom that sends buyers looking for it — a top cover that has gone soft and spongy, a belt that has grown wider and is rubbing the frame, a cover peeling at the edges — is not proof that NBR is what you need. It is proof that the current cover is dissolving in something. What that something is, how much of it there is, how hot it is and where it reaches inside the belt decide whether you need an oil-resistant cover, an oil-resistant belt, or a different conveyor.

This article separates those cases, explains what the oil-resistance grades mean and how they are tested, and lays out what to send a belting works so the quote you get back is for the belt you need rather than the belt they usually sell.

What oil does to a standard belt

General-purpose belt covers are built on SBR or natural rubber blends. Both are hydrocarbons, and mineral oils, greases and many vegetable oils are hydrocarbon solvents to them. The oil does not attack the rubber chemically; it diffuses into it. The rubber swells, the cross-linked network is pushed apart, and the cover loses hardness, tensile strength and abrasion resistance in that order. On a running belt you see it as:

  • Softening and swelling at the loading point first, where oil concentration and contact are highest.
  • Belt growth in width, sometimes enough to foul skirts and the frame, because a swollen cover has nowhere else to go.
  • Cover-to-carcass separation, because the swollen cover is under stress the bond was not designed for.
  • Wicking into the carcass from cut edges and from mechanical fastener holes, after which the fabric plies delaminate from the inside and no cover grade will save the belt.
  • Splice failure, because splice adhesives and cold-bond cements are generally as oil-sensitive as the covers.

The wicking point matters most for buyers. A belt with an oil-resistant cover and a standard carcass, cut to length on site with exposed edges, will fail from the edges in oily service exactly as a standard belt would. "Oil-resistant belt" should mean oil-resistant covers, oil-resistant skim between the plies, and sealed or oil-resistant edges. Ask for all three to be stated.

Which oil: the question that decides the compound

Not all oils swell rubber equally, and the compound that handles one may fail with another. The main groups a belting buyer meets:

Mineral oils and greases — lubricants, hydraulic fluid, diesel, machine oil on recycled scrap. The classic case for NBR, which is a copolymer of butadiene and acrylonitrile; the acrylonitrile content (ACN) sets the oil resistance, and higher ACN means less swell in mineral oil at the cost of low-temperature flexibility.

Vegetable and animal oils — soybean, palm, rapeseed, tallow, fish oil. These are the belts on grain and oilseed lines, feed mills, rendering and food processing, and they are underrated. Soybean meal and oilseed cake carry enough residual oil to swell a standard cover over a season; a grain elevator belt that has "gone soft on the top" is usually this. NBR handles most of them, but the swell in a given vegetable oil is not the same as in the mineral oil the datasheet was tested with. Ask for the test fluid.

Aromatic and chlorinated solvents — some chemical process duties. NBR is poor against many of these; other polymers apply and the question is outside a standard belting quote.

Fertiliser, salts and mild chemicals — do not swell rubber but can attack it, and chlorine or ozone will crack a standard cover regardless of oil. This is a chemical-resistance question and often points toward a different compound entirely.

The consequence for the inquiry: name the oil, its concentration on the material, and the temperature. "Oil-resistant" without those is a request for the supplier's default grade, which will be the cheapest thing they call NBR.

Grades and the test behind them

Belting suppliers describe oil resistance in three overlapping vocabularies, and a quotation may use any of them.

Designation Where it comes from What it means in practice
G DIN 22102 cover grade letter for oil- and grease-resistant covers A grade name, not a test result; the standard sets requirements but the number that matters is the swell measured on the actual compound
MOR — moderate oil resistance Trade designation, common in North American and Chinese quotations Usually a blended compound for light oil exposure — vegetable oil residue on grain, occasional lubricant contact
SOR — superior or severe oil resistance Trade designation Usually a higher-ACN NBR for continuous mineral oil exposure — scrap, machining swarf, oily recycling
NBR The polymer, not a grade Tells you the base rubber; says nothing about ACN content, filler loading or the swell achieved
ISO 1817 volume swell The test method — a rubber sample immersed in a reference fluid at a set temperature for a set time, and its volume change measured The only one of these that is a number you can compare across suppliers, provided the fluid, temperature and time are the same

The insider point is in the last row. Two works can both quote "SOR NBR" and deliver compounds whose ISO 1817 swell in the same oil differs by a wide margin, because one used a high-ACN polymer and the other stretched a low-ACN grade with cheap filler. The test method exists precisely because the grade name cannot be trusted alone. When you compare oil-resistant belt quotes, ask for the ISO 1817 result, the reference fluid (the ASTM reference oils IRM 901 and IRM 903 are the common ones for mineral oil; for vegetable oil ask them to test in your oil), the temperature and the immersion time — and compare only like with like. The broader question of why Chinese quotes for the same specification differ applies with unusual force to compound grades, because the difference is invisible on the roll and shows up a year later.

When NBR earns its cost — and when it does not

An NBR cover costs more than SBR, and an SOR grade more than MOR. Whether the premium pays back is a question of exposure, not of principle.

NBR pays for itself when:

  • Oil is present at the loading point continuously — scrap metal with cutting fluid, oily swarf, soybean meal, rendered product, recycled plastic with residual lubricant.
  • The current belt is being replaced because of swelling rather than because of wear. If the cover is worn thin and also soft, oil is a contributor; if it is thick and soft, oil is the cause.
  • Belt width growth is fouling the structure, which is a shutdown risk rather than a wear cost.
  • The belt runs hot as well as oily. Heat accelerates oil absorption, and a standard cover that survived cold oil will not survive warm oil. Where heat is the dominant factor the separate guide on heat-resistant grades applies alongside this one.

NBR is the wrong purchase when:

  • The oil exposure is intermittent and light, and the belt is failing from abrasion. A better abrasion grade, covered in the cover rubber abrasion article, fixes the actual failure; NBR compounds are generally less abrasion-resistant than a good SBR at the same cover gauge.
  • The failure is in the carcass, splice or edges. An NBR cover on a standard carcass in continuous oil service is the most expensive way to fail slowly.
  • The "oil" is actually a solvent or an oxidising chemical. NBR may be worse than a standard cover against some of those.
  • The belt needs low-temperature flexibility. High-ACN NBR stiffens in cold; an oily belt on an outdoor conveyor in a cold climate is a specification that needs both properties balanced, and it will not come off the shelf.

Ask any supplier for the NBR and the SBR construction quoted on the same sheet, same carcass, same cover gauge, so the premium is visible as a number rather than a feeling.

Specifying an oil-resistant belt: the process

Work through these in order. Most oil-resistant belt returns trace to a step here that was skipped.

  1. Identify the fluid. Name it, state the approximate proportion on the material, and note whether it is warm. If you are unsure, send a sample of the material to the supplier — a bag of soybean meal or a jar of the cutting fluid — and ask them to immerse a compound sample in it.
  2. Decide the exposure class. Continuous mineral oil is SOR territory. Vegetable oil residue on grain is usually MOR. Occasional contact on an otherwise abrasive duty may be a standard belt with a better abrasion grade.
  3. Specify covers, skim and edges together. Top cover, bottom cover, skim between plies, and edge treatment — moulded edges from the press, or cut edges sealed with an oil-resistant compound. State which.
  4. Specify the carcass. EP fabric is standard; the oil does not attack polyester or nylon much, so the carcass concern is wicking and delamination, addressed by the skim and edges rather than by a different fabric.
  5. Specify the splice. If the belt will be hot-vulcanised endless, ask for the splice compound to be the same oil grade as the belt. If it will be cold-bonded or mechanically fastened, ask what adhesive or fastener rubber is supplied and whether it is oil-rated.
  6. Ask for the ISO 1817 result on the compound to be supplied, in the fluid, temperature and time you specify, from the supplier's own laboratory or from the compounder's.
  7. Order a trial length before a programme, install it on the worst-affected conveyor, and measure cover hardness and belt width at commissioning and monthly. Softening shows within a few months in genuine oil service.
  8. Cut and retain a reference sample from the delivered roll. If the belt swells early, a laboratory can compare the delivered compound to the trial compound and settle whether you got what you tested.

Common questions

Is a food-grade white belt the same as an oil-resistant belt?

No. Food-contact compounds are formulated for what they leach into the product; oil-resistant compounds are formulated for what the product does to them. A grain or food line may need both — oil resistance for the oilseed residue and a food-contact declaration for the duty — and they are separate specifications with separate evidence. Confirm any food-contact claim in writing and separately from the oil grade.

Can a standard belt be treated or coated to resist oil?

Not in a way that lasts. Surface coatings wear through at the loading point in weeks and the oil then does what it would have done anyway. Oil resistance has to be in the bulk of the cover compound.

Why did my NBR belt swell anyway?

The usual reasons, in order of frequency: the oil was not the one the compound was tested against; the belt was oil-resistant on the covers only and wicked through the edges or fastener holes; the belt ran hotter than the compound's test temperature; or the compound delivered was not the compound sampled. The retained reference sample is how you tell the last case from the others.

Does an NBR cover affect belt tracking or cleaning?

Marginally. NBR compounds can have a different friction coefficient against pulley lagging than SBR, and a swollen belt of any compound tracks badly. The bigger practical difference is that scrapers on oily belts need more frequent attention because the residue is sticky, which is a housekeeping point rather than a belt point.

What to ask the supplier next

Before a first order of oil-resistant belting from any works, these go in the inquiry, and the answers — along with the standard document set to request from a Chinese supplier before a first order — go in the file.

  • Which oil-resistant grades do you produce — NBR, MOR, SOR or a G-grade to DIN 22102 — and what is the polymer base and approximate ACN content of each?
  • Do you compound in-house or buy the compound in? Either is acceptable; what matters is whether ISO 1817 swell data exists for the compound as it will be pressed, and who can supply it.
  • Can you provide an ISO 1817 volume-swell result in my fluid, at my temperature, with the laboratory, holder name and date on the report?
  • Are the skim compound and edge treatment oil-rated to match the covers? Have it stated on the construction sheet.
  • What splice materials ship with the belt, and are they oil-rated?
  • Is the sample cut from the production press batch, and what is the sample cost and whether it is credited on the first order?
  • Can you quote the same construction in a standard SBR cover so the oil-grade premium is visible?

Jiutong Conveyor Belting, a rubber belting works registered in 2024 in Boye County, Baoding — a district where compounding and vulcanising capacity sit close to the belt makers — lists grain, feed and processing conveyors among its applications, tells buyers to confirm any oil-resistant grade at inquiry, and states one-piece MOQ with custom samples in around ten working days, which fits a single trial length on an oily conveyor before a programme. Which oil grades it runs and whether swell data exists behind them are not on its factory profile; ask, and read whatever comes back for the fluid, temperature and issuing laboratory before reading it for the number.